Android Phone Not Detecting Your Tracker?

If your SecurityBase or AusFindr tracker is activated and you performed a reset, but your Android phone isn't showing the setup pop-up, work through the steps below in order. Most issues are fixed by Step 1 or Step 2.

Before you start: make sure your tracker is in pairing mode and held close to your phone (within about 10 cm). Your phone needs to be running Android 9 or later with Google Play services. Find Hub was previously called "Find My Device", so you may see either name.

Step 1: Turn on "Scan for nearby devices"

Android only shows the setup pop-up if this setting is on. It's the most common cause of the problem.

  • Most Android phones: Settings > Google > Devices & sharing > Devices > turn on Scan for nearby devices. On some versions the path is Settings > Google > All services > Devices.
  • Android 14 and newer: Settings > Connected devices > Connection preferences > Fast Pair. If you can't find it, type "nearby devices" into the Settings search bar.
  • Samsung Galaxy: Settings > Connections > More connection settings > turn on Nearby device scanning.
  • Google Pixel: also check Settings > Location > Location services > Bluetooth scanning.

Then put your tracker back into pairing mode.

Step 2: Check Bluetooth and Location

Both must be on, or the pop-up won't appear.

  1. Swipe down and confirm Bluetooth is on.
  2. Go to Settings > Location and confirm Location is on.
  3. Make sure your phone is unlocked, awake and connected to the internet (Wi-Fi or mobile data).

Step 3: Wait out a dismissed pop-up

If you swiped away the pop-up a couple of times, Android may stop showing it for several minutes. Wait about five minutes, then put your tracker back into pairing mode by activating it.

Step 4: Restart Bluetooth and your phone

  1. Turn Bluetooth off, wait 10 seconds, then turn it on again.
  2. Fully close the Find Hub app.
  3. Restart your phone, then try again.

Step 5: Update and refresh Google's apps

  1. Open the Google Play Store and update Find Hub and Google Play services.
  2. Still no luck? Go to Settings > Apps > Google Play services > Storage > Clear cache. Do the same for Find Hub.
  3. Restart your phone and try again.

Step 6: Check the Google account on your phone

  • If your phone has more than one Google account, open Find Hub, tap your profile picture (top right) and switch accounts. Try pairing under each one.
  • If many phones are signed into the same Google account, try pairing from a phone with only that account.

Step 7: Make sure the tracker isn't still linked to another account

A tracker that was previously set up (for example, if you tested it earlier or connected to another account) may need to be released first.

  1. On the phone or account it was originally paired to, open Find Hub, select the tracker and tap Remove device.
  2. Factory reset the tracker as per the manual.
  3. Put it into pairing mode and try again.

Step 8: Use the setup pop-up, not standard Bluetooth pairing

Trackers that work with Find Hub connect through Google's pairing pop-up (Fast Pair). Wait for the pop-up rather than using "Pair new device" in your Bluetooth settings.

Step 9: Check your phone is compatible

  • The Find Hub network needs Android 9 or later.
  • Your phone needs Google Play services. Phones without it, such as some Huawei models or phones running custom operating systems like GrapheneOS or /e/ OS, usually can't show the pop-up.
  • If possible, try a second Android phone. Some phones have Bluetooth quirks that stop the pop-up appearing, and testing a second phone helps confirm whether the issue is the phone or the tracker.

Helpful Google resources

Tracker Card Troubleshooting

If your tracker card is not connecting, not showing in the app or doesn't seem to charge properly, please check the steps below.

  • Make sure you are setting up the right card for your phone:

    • Apple Find My card for iPhone and Apple’s Find My app
    • Android card for Android phones and Google Find Hub

    You can confirm the version on the bottom left of the card, which will indicate 'Locate with Apple Find My or Locate with Android Find Hub'. The Apple and Android versions are different products and are not interchangeable.

    If you ordered the incorrect version, please let us know via the form below, and we can organise an exchange.

  • Make sure your phone supports the tracking network used by your card.

    • Apple cards require an iPhone with the Find My app enabled
    • Android cards require a compatible Android phone with Find Hub installed (download here) and Find My Device settings enabled

    Please ensure the phone operating system (iOS for Apple or Android) is up to date.

  • Your phone needs the right settings turned on for the tracker card to connect properly.

    • Bluetooth should be turned on
    • Wi-Fi should be enabled
    • Location Services should be turned on
    • On Android, also make sure Find My Device / Find Hub are enabled (Settings → Google → All services → Devices → Scan for nearby devices). The Android tracker requires the Scan for nearby devices setting to be on, not just Bluetooth. See this video for the key settings in Android.
    • On iPhone, make sure Find My is enabled

    Even if you are not connected to Wi-Fi, having Wi-Fi enabled can still help with location and discovery.

  • A low battery can cause the card to fail to connect properly or even become unresponsive.

    • Place the card on a wireless charger.
    • Place the card slightly off-centre, as shown in the picture in the manual for your card; the charging coil is on the left side of the card.
    • Please note that the card may not charge if it is placed directly in the centre of the charger.
  • If the card still is not connecting, restart your phone and then try the setup again. This can help refresh Bluetooth, location services and background processes that may be interfering with the connection.

  • If the card is still not connecting, perform a reset as described in step 4 in the manual and try again.

    Please note the presses for the reset sequence need to be done at the right pace (too fast or too slow won’t work) because the sequence is intentionally designed to prevent anyone who finds the card from easily disabling it.

  • The tracker card sends out a Bluetooth signal every few minutes, but the location in Find Hub / Find My may not update instantly or with every short movement. If you walk a short distance, such as to the end of the street, the app may continue showing the previous location for a while before refreshing. This is normal and helps preserve battery life. The location should update once the card is detected again and the app/network refreshes the location. Updates are more frequent in areas with more phones to detect the card.

    To test the card, take it with you to another location, such as a shopping centre, supermarket or busy public area, and check whether the tracker’s location updates after a few minutes.

    If the location is not updating after a few minutes or in a different spot, please check the following:

    • the card has enough charge
    • the card has been set up correctly
    • the card is in an area where nearby compatible devices are likely to pass by

    If the card is in a quiet area, inside a signal-blocking bag, or not near compatible devices, location updates may be less frequent. The card can only update its location when it is detected by a device that is part of the network.

    For more information, please see this page.

  • Apple Find My and Google Find Hub use nearby Apple or Android devices to securely detect your tracker and update its location in the app.

    For more detail see this page.

  • If the tracker card does not seem to be charging, first make sure it is placed correctly on a Qi certified wireless charger.

    • Place the card slightly off-centre, as shown in the picture in the manual for your card; the charging coil is on the left side of the card.
    • The card may not charge if it is placed directly in the centre of the charger.
    • Please note the card may not charge properly on non-Qi-certified chargers, including watch chargers, dual chargers and 3-in-1 style chargers. These chargers often use smaller charging coils, which can make them difficult to align with the charging coil inside the tracker card. You can check here whether your charger is Qi-certified.

    Also see the 'Charging the card' section in the manual.

Further assistance

If you have tried the steps above, checked the troubleshooting scenarios, and your tracker card still is not working as expected, please complete the form below and we are happy to assist.

We will get back to you via phone or email the same day!